Contents

- 1 How do I know what size carburetor to get?
- 2 How much horsepower will a 650 cfm carb support?
- 3 How much horsepower will a 750 cfm carb support?
- 4 What happens if your carburetor is too big?
- 5 Does a carburetor add horsepower?
- 6 Is a 650 cfm carb to big for a 350?
- 7 Are carb spacers worth it?
- 8 What size carburetor do I need for a 383 stroker?
- 9 Will a bigger carb make my bike faster?
- 10 How much horsepower will a 950 cfm carb support?
- 11 How do you increase CFM on a carburetor?
- 12 What size cfm carb do I need?

## How do I know what size carburetor to get?

To arrive at the most appropriate carburetor choice, there’s a basic formula: engine displacement multiplied by maximum rpm divided by 3,456. For example: a typical 355ci small-block—a 0.030-over rebuild—with a 6,000-rpm max engine speed would work well with a 616-cfm carb ((355 x 6,000) 3,456 = 616.32).

## How much horsepower will a 650 cfm carb support?

So, using your Google-Fu you type “How much power can a 650 cfm carb support?” Well, chances are that you’ll get answers in the 450-470 hp range, but that’s not really the right way to look at it.

## How much horsepower will a 750 cfm carb support?

A 750DP on a 330hp-400hp 5.7 with a dual plane intake (performer rpm) is easy to tune and will make max power to boot.

## What happens if your carburetor is too big?

If the barrels are too big, the loss of air velocity means the cylinder will not fill to its full capacity. An engine with a carb that is too big will put out less Torque and Horsepower. It will be difficult to drive due to poor low-end torque. If you drag race your car, an oversized carb will produce slow 60 ft.

## Does a carburetor add horsepower?

After you fix what’s limiting performance, an Edelbrock Performer intake can add as much as 10 HP. The FAQ forum is a good place to ask questions. There are differences between engines and performance improvements.

## Is a 650 cfm carb to big for a 350?

If you’re expecting a maximum of 6,500 rpm, you’re going to need a 650- to 700-cfm carburetor. These sizing numbers are only the beginning of carburetor selection—a baseline. A 600-cfm carburetor may perform quite well on a stock 350 Chevy.

## Are carb spacers worth it?

Spacers are said to improve air/fuel vaporization through and out of the carburetor. Anytime the air/fuel charge has to turn sharply coming off the carb, it increases the chance of separating the fuel from the air.

## What size carburetor do I need for a 383 stroker?

Carburetor For 383 Stroker recommends a 650 cfm carburetor. A 750 cfm carburetor will make the engine more powerful, but it is the largest that should be used unless the engine is being used for racing.

## Will a bigger carb make my bike faster?

A bigger carburetor alone will not make your bike go faster. In most cases, your bike won’t even start or idle roughly with a carburetor that’s too big. For more power, you should look into a full system performance exhaust and rejetting your carb (not replacing it entirely).

## How much horsepower will a 950 cfm carb support?

Although way too small according to the CFM calculations presented earlier, a 950 Ultra HP can pass enough air to support more than 800 hp from a street/strip 572. If you do the math in terms of the required CFM, these carbs look far too small to be able to allow the production of such big horsepower numbers.

## How do you increase CFM on a carburetor?

In just a few minutes working with a file, you can augment this mod by applying a radius to the top edges of the choke horn. This increases the flow about 3 to 5 more cfm. You may see carbs that have been reworked for a higher performance by milling off the choke horn.

## What size cfm carb do I need?

The engine’s volumetric efficiency is a measurable value and with a correctly matched carburetor you will receive the best performance possible out of your engine. The formula for calculating how much CFM (cubic feet per minute) an engine requires is: CFM = Cubic Inches x RPM x Volumetric Efficiency ÷ 3456.