- 1 Where is the model number on a Homelite weed eater?
- 2 Do weed eaters have serial numbers?
- 3 How can I tell how old my Homelite chainsaw is?
- 4 Are Homelite weed eaters any good?
- 5 Why is my weed eater not pumping gas?
- 6 How do you clean a carburetor?
- 7 How do I look up a serial number?
- 8 What does the R mean on Stihl trimmers?
- 9 How do you adjust a carburetor?
- 10 Why does weed eater bog down when accelerating?
- 11 What size string does a Homelite weed eater take?
Where is the model number on a Homelite weed eater?
What’s my model number? Homelite model numbers are found on the data plate or data label on the machine. This is usually located on the back or bottom of the unit.
Do weed eaters have serial numbers?
On homeowner trimmers, it is located on the bar code label on the fan casing. On professional units and brushcutters it is on the bar code label and stamped in the top of the cylinder or main crank case. All current serial numbers will be nine digits long and begin with the numbers 1, 2, 5, 8 or 9.
How can I tell how old my Homelite chainsaw is?
In order to determine the year the Homelite saw was made, product and serial numbers should be used.
- Look inside the owner’s manual of the chainsaw to see if there is a small sticker on it with two numbers.
- Check near the base of the saw casing on the left-hand side to find a small sticker.
- Call (800) 242-4672.
Are Homelite weed eaters any good?
It does fine, not as loud as my old Stihl but it did a good job. My only complaint is the fuel tank is too small, cutting down on use time. UPDATE: So far this summer the Homelite 26cc trimmer has proven to be a disappointment. It simply is not powerful enough to get the job done.
Why is my weed eater not pumping gas?
Cleaning the carburetor will usually cure this problem. To clean the carburetor it has to be removed from the engine. Just be sure to note the fuel line configuration before removing them. Once it is removed, disassemble the carburetor and inspect the diaphragm and the plastic flapper.
How do you clean a carburetor?
Directions for How To Clean A Carburetor:
- Dilute cleaner. In a large container, mix 1 part Simple Green Pro HD Heavy-Duty Cleaner to 3 parts water.
- Clear air filter.
- Remove the carburetor.
- Remove carburetor float.
- Remove other removable components.
- Soak and scrub components.
- Rinse and dry.
- Reassemble and replace.
How do I look up a serial number?
- Open Command Prompt by pressing the Windows key on your keyboard and tapping the letter X.
- Type the command: WMIC BIOS GET SERIALNUMBER, then press enter.
- If your serial number is coded into your bios it will appear here on the screen.
What does the R mean on Stihl trimmers?
In short, our professional trimmers don’t mess around. To help you identify model features, look for these corresponding symbols: C = Comfort feature, E = Easy2Start™, R = loop handle, and X = lightweight version.
How do you adjust a carburetor?
Here’s How To Adjust a Carburetor
- Remove the Engine Air Filter. The air cleaner and filter assembly must be removed for you to access the carburetor.
- Locate Adjustment Screws.
- (Optional): Hook up Vacuum Gauge.
- (Optional): Set Baseline.
- Warm the Engine Up.
- (Optional): Adjust Idle Speed Screw.
- Adjust the Air-Fuel Mixture.
Why does weed eater bog down when accelerating?
The most common causes of a weed eater dying when throttled are fuel issues, insufficient air intake, or problems with the exhaust. You should follow the path that the fuel travels to identify the issue.
What size string does a Homelite weed eater take?
String Trimmers. This Homelite 26-cc, gas curved shaft string trimmer has a curved shaft and weighs 10.2 lbs. It uses dual 0.080-inch cutting lines on a 17-inch diameter head.