Quick Answer: What Carburetor For Ford 385 Egine?

What size carburetor is correct for my engine?

The engine’s volumetric efficiency is a measurable value and with a correctly matched carburetor you will receive the best performance possible out of your engine. The formula for calculating how much CFM (cubic feet per minute) an engine requires is: CFM = Cubic Inches x RPM x Volumetric Efficiency รท 3456.

What carburetors did Ford use?

Ford trucks, Lincoln cars, Jeep and AMC continued to use Autolite four- barrels with a third generation carburetor referred to as the model 4350.

What’s the best carburetor for performance?

Best Sellers in Automotive Performance Carburetors

  1. #1. Spectre Performance 5776 1″ Open Carb Spacer with Tube.
  2. #2. Edelbrock 9905 Performer 600 CFM Manual Choke Remanufactured Carburetor.
  3. #3. Proform 141-200 69-91 SBC Timing Tab – 6.75/7.00 Balancer.
  4. #4. Edelbrock 8711 Phenolic Carburetor Spacer, Black.
  5. #5.
  6. #6.
  7. #7.
  8. #8.

What size carburetor do I need for a Ford 460?

The best option is to buy a 600 to 750 CFM carburetor to maximize the powerful capabilities of this engine. The 460 was a less popular model to the 429 that saw extensive use and was popular in many applications.

You might be interested:  Often asked: What Maintains A Constant Gasoline Level In The Carburetor?

What cfm carb do I need for a 350?

A 600-cfm carburetor may perform quite well on a stock 350 Chevy. However, the minute you start weaving in power adders like a hotter cam, a dual-plane performance intake manifold, and aluminum heads you’re going to need 700-750 cfm.

What happens if your carburetor is too big?

If the barrels are too big, the loss of air velocity means the cylinder will not fill to its full capacity. An engine with a carb that is too big will put out less Torque and Horsepower. It will be difficult to drive due to poor low-end torque. If you drag race your car, an oversized carb will produce slow 60 ft.

What year did Ford stop using carburetors?

When did Ford stop using carbs? In the U.S. market, the last cars using carburetors were: 1990 (General public): Oldsmobile Custom Cruiser, Buick Estate Wagon, Cadillac Brougham, Honda Prelude (Base Model), Subaru Justy. 1991 (Police): Ford Crown Victoria Police Interceptor with the 5.8 L (351 cu in) V8 engine.

How do I identify my Motorcraft carburetor?

Size. Identifying a Motorcraft or Autolite carburetor can be done by identifying the throttle bore size. Each carburetor has the bore size cast into the carburetor as a diameter size measured in inches.

How much horsepower will a 650 cfm carb support?

So, using your Google-Fu you type “How much power can a 650 cfm carb support?” Well, chances are that you’ll get answers in the 450-470 hp range, but that’s not really the right way to look at it.

Who makes the most reliable carburetor?

Out of 13 brands of carburetors, enthusiasts elected Advanced Engine Design (AED), Edelbrock, and Holley (in alphabetical order) as the top 3 most reliable brands of carburetors.

You might be interested:  Readers ask: How To Connect A Fuel Pressure Regulator When Converting To Carburetor?

How much horsepower does a carburetor add?

After you fix what’s limiting performance, an Edelbrock Performer intake can add as much as 10 HP. The FAQ forum is a good place to ask questions. There are differences between engines and performance improvements.

What is the difference between a Holley 4150 and 4160 carburetor?

These two are very similar with the primary difference that the 4150 uses a thick metering block in both the primary and secondary while the 4160 is shorter in length and uses a thin, metering plate on the secondary side.

What is a Ford 460?

Ford’s most popular, longest-lasting big block V8 engine lived an incredibly varied life. The 460 cubic inch eight-cylinder motor debuted all the way back in 1968 but found itself powering cars, trucks, and commercial equipment all the way to the end of the 1990s during its three decade run.

What is a 600 CFM carburetor?

A 600 CFM carburetor can be a great choice for a wide variety of engines. They can be a perfect match for a highly tuned race engine around 300 cubic inches all the way up to a street tuned big block.

Leave a Reply

Your email address will not be published. Required fields are marked *