- 1 How do you adjust a Stihl carburetor?
- 2 What is the LA screw on a Stihl chainsaw?
- 3 What does L and H mean on a carburetor?
- 4 How do you adjust a high speed screw on a Stihl chainsaw?
- 5 Why does my chainsaw dies when I give it gas?
- 6 Why does my chainsaw bog down when I give it gas?
- 7 How do I know if my carburetor is rich or lean?
- 8 How do you adjust H and L screws on a carburetor?
- 9 Is it better to run lean or rich?
- 10 How do you adjust the fuel mixture on a chainsaw?
How do you adjust a Stihl carburetor?
Start the trimmer and hold the throttle trigger in all the way to get the trimmer head spinning at maximum speed. Turn the H screw clockwise with a carburetor adjustment tool until the head is spinning as fast as it will go, then back off the screw carefully until the RPMs start to decrease.
What is the LA screw on a Stihl chainsaw?
The LA setting on Stihl chainsaws is controlled by a screw on the outer housing of the engine that adjusts the flow of fuel and air through the carburetor. This screw is inside the engine housing on the carburetor, but is accessible through a hole or gap in the outer housing of the saw.
What does L and H mean on a carburetor?
The letters on the screws represent High (H), Low (L) and Idle (T). The H screw regulates the Air/Fuel mix during high RPMs, while the L Screw does the same during low RPMs. The T screw regulates how much fuel is sent to the carburettor while idling until the throttle is pressed.
How do you adjust a high speed screw on a Stihl chainsaw?
They are the high-speed, low-speed and idle adjustments respectively. Determine the carburetor type before adjusting the high- and low-speed screws. To do this, turn the “L” screw clockwise as far as it will go, using a flat-head screwdriver, then turn it counterclockwise as far as it will go.
Why does my chainsaw dies when I give it gas?
Because your chainsaw will idle, but dies when it is revved up to full power, it means that the filter is only partially clogged; it will allow enough fuel to the engine to run on idle, but not enough to sustain full throttle. If the filter becomes clogged, not enough fuel will reach the engine for it to run properly.
Why does my chainsaw bog down when I give it gas?
If your chainsaw is bogging down when you give it throttle, this is often a sign of improper gas-to-oil ratio. If there is too much gasoline in relation to the amount of oil used, this is known as a “rich mixture” and can cause the chainsaw to run poorly.
How do I know if my carburetor is rich or lean?
Q: How Do You Tell if a Carburetor Is Rich or Lean? A: One way to tell for sure is by “reading” the spark plugs. If the plug tip is white, the mixture is lean. If it’s brown or black, it’s rich.
How do you adjust H and L screws on a carburetor?
Set the idle speed screw(not L or H) so it is just able to idle by itself. This screw will have a “stop” it rests against. Now turn the L screw out until in decreases in rpm and then back in(very slowly) until it is at peak rpm. Adjust the H screw once more as above and it should be a very serviceable 2 stroke.
Is it better to run lean or rich?
TLDR – running just a little lean could improve fuel economy and give extra power. However, run too lean and you risk engine failure because the engine runs too hot. Whereas running rich can waste fuel and increase pollution but will not damage the engine. You ideally want to run at the perfect ratio of 14.7:1.
How do you adjust the fuel mixture on a chainsaw?
Carburetor Adjustment Procedure
- Before you start the saw, locate a small flat-bladed screwdriver.
- Begin by checking the saw’s air filter.
- Check the fuel level.
- Start the engine and warm it up.
- Begin by setting the idle speed.
- Set the low speed fuel adjustment.
- Go back to step (4) and reset the idle speed.