- 1 What size carb do I need for a 383 stroker?
- 2 How much horsepower will a 650 cfm carb support?
- 3 How much horsepower will a 750 cfm carb support?
- 4 What is a better carburetor Holley or Edelbrock?
- 5 Is a 650 cfm carb to big for a 350?
- 6 What happens if your carburetor is too big?
- 7 Do carb spacers add horsepower?
- 8 How much horsepower does 383 stroker have?
- 9 How do I know what cfm carb I need?
- 10 Are carb spacers worth it?
- 11 How much horsepower will a 950 cfm carb support?
- 12 How much horsepower does a carburetor add?
- 13 Who makes the most reliable carburetor?
- 14 Is quick fuel made by Holley?
- 15 What is the difference between a Holley 4150 and 4160 carburetor?
What size carb do I need for a 383 stroker?
Carburetor For 383 Stroker recommends a 650 cfm carburetor. A 750 cfm carburetor will make the engine more powerful, but it is the largest that should be used unless the engine is being used for racing.
How much horsepower will a 650 cfm carb support?
So, using your Google-Fu you type “How much power can a 650 cfm carb support?” Well, chances are that you’ll get answers in the 450-470 hp range, but that’s not really the right way to look at it.
How much horsepower will a 750 cfm carb support?
A 750DP on a 330hp-400hp 5.7 with a dual plane intake (performer rpm) is easy to tune and will make max power to boot.
What is a better carburetor Holley or Edelbrock?
As I mentioned before, right out of the box an Edelbrock will be better. However, if you’re a DIY guy who likes modding things around – Holley will be your best pal. The tuning is more responsive and less touchy than not only Edelbrock, but most other manufacturer’s carbs.
Is a 650 cfm carb to big for a 350?
If you’re expecting a maximum of 6,500 rpm, you’re going to need a 650- to 700-cfm carburetor. These sizing numbers are only the beginning of carburetor selection—a baseline. A 600-cfm carburetor may perform quite well on a stock 350 Chevy.
What happens if your carburetor is too big?
If the barrels are too big, the loss of air velocity means the cylinder will not fill to its full capacity. An engine with a carb that is too big will put out less Torque and Horsepower. It will be difficult to drive due to poor low-end torque. If you drag race your car, an oversized carb will produce slow 60 ft.
Do carb spacers add horsepower?
Yes, they will give you more horsepower. But carb spacers have another important function. They also act as insulators which keep engine heat away from your carburetor to ensure cooler incoming air and fuel.
How much horsepower does 383 stroker have?
The 383 stroker engines have been reported to achieve 330 horsepower with 410 foot-pounds of Torque, 395 horsepower with 410 foot-pounds of Torque and 395 horsepower with 410 foot-pounds of Torque.
How do I know what cfm carb I need?
The volumetric efficiency of the engines is a measurable value, and with an adequate carburetor will get the most efficiency out of the engine. The formula to calculate the amount of CFM (cube feet per minute) that a motor needs is CFM= Cubic Inches x RPM x Volumetric Performance ÷ 3456.
Are carb spacers worth it?
Spacers are said to improve air/fuel vaporization through and out of the carburetor. Anytime the air/fuel charge has to turn sharply coming off the carb, it increases the chance of separating the fuel from the air.
How much horsepower will a 950 cfm carb support?
Although way too small according to the CFM calculations presented earlier, a 950 Ultra HP can pass enough air to support more than 800 hp from a street/strip 572. If you do the math in terms of the required CFM, these carbs look far too small to be able to allow the production of such big horsepower numbers.
How much horsepower does a carburetor add?
After you fix what’s limiting performance, an Edelbrock Performer intake can add as much as 10 HP. The FAQ forum is a good place to ask questions. There are differences between engines and performance improvements.
Who makes the most reliable carburetor?
Out of 13 brands of carburetors, enthusiasts elected Advanced Engine Design (AED), Edelbrock, and Holley (in alphabetical order) as the top 3 most reliable brands of carburetors.
Is quick fuel made by Holley?
On December 8, 2014, Holley acquired DiabloSport Inc. The industry leader in vehicle calibration.
What is the difference between a Holley 4150 and 4160 carburetor?
These two are very similar with the primary difference that the 4150 uses a thick metering block in both the primary and secondary while the 4160 is shorter in length and uses a thin, metering plate on the secondary side.