Question: What Carburetor Kit Will Fit Poulan Chainsaw “pp4218 Aux 802145?

Are Poulan and Husqvarna parts the same?

Since Poulan is owned by Husqvarna, the two brands often share technologies. Most mid-level Craftsman products in the power equipment segment are slightly altered Poulan products. Craftsman products made by Poulan have a “358” model prefix.

Why does my Poulan chainsaw dies when I give it gas?

The fuel filter might be clogged. A clogged fuel filter is often caused by leaving old fuel in the chainsaw. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the fuel filter and cause the engine to stall.

What size chain do I need for a Poulan PP4218A?

Solid Carbide Chainsaw Chain S62 Fits Poulan Pro PP4218A / PR4218 Gas – 182191 -w/ 18″ x 3/8″ Bar.

What fuel mixture does a Poulan chainsaw use?

A: Mix 3.2 ounces of Poulan 2-cycle air cooled engine oil to one gallon of fresh unleaded gasoline to obtain the recommended 40:1 fuel to oil ratio. Over a period of time oil will separate from gasoline.

You might be interested:  Readers ask: How To Repair A Briggs And Stratton Carburetor?

Is Poulan a good brand?

Poulan chainsaws have been around for quite a while and the brand has a solid reputation. For the average homeowner, Poulan Pro chainsaws are a good mid-level quality that will get the job done around the yard. Learn more about Poulan Pro Chainsaws or other Poulan Pro lawn and garden equipment by visiting their site.

Which Husqvarna chainsaws are made by Poulan?

No Poulans really are Huskys, or even Husky designs, and no Huskys are rebadged Poulans – even though Husky owns Poulan. The affected Husky models by now are the 235 and 240, before that it was the 137 and 142, then 136 and 141, and then 36 and 41 (from 1990) – always the two cheapest at any given time.

Why does my chainsaw bog out when I give it gas?

If your chainsaw is bogging down when you give it throttle, this is often a sign of improper gas-to-oil ratio. If there is too much gasoline in relation to the amount of oil used, this is known as a “rich mixture” and can cause the chainsaw to run poorly.

Why does my chainsaw dies when I give it gas?

Because your chainsaw will idle, but dies when it is revved up to full power, it means that the filter is only partially clogged; it will allow enough fuel to the engine to run on idle, but not enough to sustain full throttle. If the filter becomes clogged, not enough fuel will reach the engine for it to run properly.

How do you adjust the high and low on a Poulan chainsaw?

High and Low Speed Adjustments Start the chain saw as you normally do and let it idle, making sure the chain does not touch anything. Insert a small flat-head screwdriver into the idle speed screw and turn it clockwise to increase the engine speed if it idles too slowly.

You might be interested:  Question: How To Adjust Carburetor Air Fuel Mixture On Motorcycle?

What chain fits a Poulan wild thing chainsaw?

UpStart Components 2-Pack 18″ Semi Chisel Saw Chain for Poulan Wild Thing Chainsaws – (18 inch, 3/8″ Low Profile Pitch, 0.050″ Gauge, 62 Drive Links, CSC-S62)

Will a Stihl chain fit a Poulan saw?

This item STIHL 63PM3-56 16-inch Chain Saw Chain – Fits Homelite, Poulan, Echo, Remington and Craftsman.

What chain fits a Poulan chainsaw?

Poulan Pro Chainsaw Chains 18″ Chain.

Why is my Poulan chainsaw smoking?

An abundance of smoke emanating from the engine often indicates that an excessive amount of oil has been introduced into the oil and gasoline mixture that powers the chain saw. Empty the fuel tank of all the oil and fuel mixture and fill the tank with the newly mixed fuel and oil before using the chain saw again.

Which has more oil 40/1 or 50?

A 40:1 oil mix ratio means 40 units of gas for a single unit of oil drop. Likewise, in a 50:1 gasoline, there are 50 units of gas. So, a 40:1 oil mix is denser and lubricates better than 50:1.

Leave a Reply

Your email address will not be published. Required fields are marked *