- 1 Why does my Poulan chainsaw dies when I give it gas?
- 2 How do you adjust the carburetor on a Poulan Pro?
- 3 Why does my chainsaw dies when I give it gas?
- 4 Why does my chainsaw bog down when I give it gas?
- 5 Can’t get my Poulan chainsaw started?
- 6 How do you adjust the carburetor on a chainsaw?
- 7 How do you troubleshoot a Poulan chainsaw?
- 8 How do I know if my carburetor is rich or lean?
- 9 How do you adjust a high and low carburetor?
- 10 What is the T adjustment on a Poulan chainsaw?
- 11 How do you adjust the carburetor on a Poulan wild thing?
- 12 How do you adjust the idle on a Poulan Pro 42cc chainsaw?
- 13 Why does my chainsaw idle fast?
Why does my Poulan chainsaw dies when I give it gas?
The fuel filter might be clogged. A clogged fuel filter is often caused by leaving old fuel in the chainsaw. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the fuel filter and cause the engine to stall.
How do you adjust the carburetor on a Poulan Pro?
Insert a small flat-head screwdriver into the idle speed screw and turn it clockwise to increase the engine speed if it idles too slowly. As soon as the chain starts to move, turn the screw counterclockwise until the engine idles without dying and the chain stops moving for the correct idle speed.
Why does my chainsaw dies when I give it gas?
Because your chainsaw will idle, but dies when it is revved up to full power, it means that the filter is only partially clogged; it will allow enough fuel to the engine to run on idle, but not enough to sustain full throttle. If the filter becomes clogged, not enough fuel will reach the engine for it to run properly.
Why does my chainsaw bog down when I give it gas?
If your chainsaw is bogging down when you give it throttle, this is often a sign of improper gas-to-oil ratio. If there is too much gasoline in relation to the amount of oil used, this is known as a “rich mixture” and can cause the chainsaw to run poorly.
Can’t get my Poulan chainsaw started?
If your Poulan chain saw won’t start, the first thing to check is the fuel. Then turn the saw on, hold it firmly and pull the start rope in short, brisk pulls until it starts. If it doesn’t start within 15 pulls, the spark plug is likely wet-fouled. Remove it and check for moisture on the electrode.
How do you adjust the carburetor on a chainsaw?
How to Tune a Chainsaw Carburetor
- Start your saw and run it for a few minutes to warm it up.
- Set your saw down, let it idle for 30 seconds, and then pick it up and tip it forward (handle up and bar down).
- If it keeps running, go to Step 4.
- Rev (accelerate) the idling saw.
- If it accelerates fine, go to Step 6.
How do you troubleshoot a Poulan chainsaw?
Poulan Pro Chainsaw Troubleshooting
- Make sure you are starting the engine properly.
- Fill the tank with the correct fuel mixture.
- Clean the saw blade.
- Check the fuel line for kinks or leaks.
- Replace the fuel filter.
- Clean the air filter.
- Remove and replace the spark plug.
How do I know if my carburetor is rich or lean?
Q: How Do You Tell if a Carburetor Is Rich or Lean? A: One way to tell for sure is by “reading” the spark plugs. If the plug tip is white, the mixture is lean. If it’s brown or black, it’s rich.
How do you adjust a high and low carburetor?
Locate the two fuel-adjustment screws on the side of the carburetor. One will be labeled “Hi” and the other “Lo.” The “Hi” screw regulates the engine at full throttle and the “Lo” regulates the fuel when the engine is idling.
What is the T adjustment on a Poulan chainsaw?
The screw on top — marked “T” — is for adjusting the fuel mixture while the engine is idling. Of the two underneath it, the one on the left is for adjusting the mixture when the engine is running a low speed, and the one on the right is for making the same adjustment when the engine is running at high speed.
How do you adjust the carburetor on a Poulan wild thing?
Never adjust the carburetor on a cold engine. While idling, turn the “L” screw clockwise all the way in until the engine makes a higher-pitched whine. Back the screw out one-quarter turn and note its position. Then turn it back counterclockwise until the engine starts running rough or dies.
How do you adjust the idle on a Poulan Pro 42cc chainsaw?
If the engine sputters or stalls quickly, the idle speed is too slow. Turn the T-screw one-quarter turn clockwise and restart the saw. If the saw idles too slowly, adjust the T-screw another quarter-turn clockwise and check it again. Repeat this process until the saw idles without stalling.
Why does my chainsaw idle fast?
The most probable – and easiest to fix – cause of chain rotation while the chainsaw engine idles is a poorly adjusted idle setting on the carburetor. The result is that too much fuel is delivered to the combustion chamber when the throttle is released, and the engine doesn’t really slow.