- 1 How do you adjust the idle on a Poulan Pro 42cc chainsaw?
- 2 Why does my Poulan chainsaw dies when I give it gas?
- 3 Why does my chainsaw dies when I give it gas?
- 4 Why does my chainsaw bog down when I give it gas?
- 5 How do you adjust the high and low on a Poulan chainsaw?
- 6 How do you adjust a high and low carburetor?
- 7 Can’t get my Poulan chainsaw started?
- 8 Where is idle screw on Poulan Pro chainsaw?
- 9 How do you troubleshoot a Poulan chainsaw?
- 10 Why does my chainsaw only runs on choke?
- 11 Is a Poulan Pro chainsaw any good?
- 12 How do you adjust the carburetor on a chainsaw?
How do you adjust the idle on a Poulan Pro 42cc chainsaw?
If the engine sputters or stalls quickly, the idle speed is too slow. Turn the T-screw one-quarter turn clockwise and restart the saw. If the saw idles too slowly, adjust the T-screw another quarter-turn clockwise and check it again. Repeat this process until the saw idles without stalling.
Why does my Poulan chainsaw dies when I give it gas?
The fuel filter might be clogged. A clogged fuel filter is often caused by leaving old fuel in the chainsaw. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the fuel filter and cause the engine to stall.
Why does my chainsaw dies when I give it gas?
Because your chainsaw will idle, but dies when it is revved up to full power, it means that the filter is only partially clogged; it will allow enough fuel to the engine to run on idle, but not enough to sustain full throttle. If the filter becomes clogged, not enough fuel will reach the engine for it to run properly.
Why does my chainsaw bog down when I give it gas?
If your chainsaw is bogging down when you give it throttle, this is often a sign of improper gas-to-oil ratio. If there is too much gasoline in relation to the amount of oil used, this is known as a “rich mixture” and can cause the chainsaw to run poorly.
How do you adjust the high and low on a Poulan chainsaw?
High and Low Speed Adjustments Start the chain saw as you normally do and let it idle, making sure the chain does not touch anything. Insert a small flat-head screwdriver into the idle speed screw and turn it clockwise to increase the engine speed if it idles too slowly.
How do you adjust a high and low carburetor?
Locate the two fuel-adjustment screws on the side of the carburetor. One will be labeled “Hi” and the other “Lo.” The “Hi” screw regulates the engine at full throttle and the “Lo” regulates the fuel when the engine is idling.
Can’t get my Poulan chainsaw started?
If your Poulan chain saw won’t start, the first thing to check is the fuel. Then turn the saw on, hold it firmly and pull the start rope in short, brisk pulls until it starts. If it doesn’t start within 15 pulls, the spark plug is likely wet-fouled. Remove it and check for moisture on the electrode.
Where is idle screw on Poulan Pro chainsaw?
Locating the Adjustment Screws The carburetor is located just behind the air filter, which is under a cover attached to the top of the engine. Remove this cover with a T-27 screwdriver to access the adjustment screws, which are usually on the left side of the engine as viewed when holding the chain in front of you.
How do you troubleshoot a Poulan chainsaw?
Poulan Pro Chainsaw Troubleshooting
- Make sure you are starting the engine properly.
- Fill the tank with the correct fuel mixture.
- Clean the saw blade.
- Check the fuel line for kinks or leaks.
- Replace the fuel filter.
- Clean the air filter.
- Remove and replace the spark plug.
Why does my chainsaw only runs on choke?
If your chainsaw only runs with the choke on, it is likely an issue with your carburetor. If the carburetor is plugged, the engine will be starved of fuel and will not run. However, if the engine is plugged, the choke will pull more fuel through the carburetor’s idle circuit and allow it to run.
Is a Poulan Pro chainsaw any good?
Even though Poulan chainsaws share a lot of the same technology as their Husqvarna cousins, they tend to be a lot cheaper. This makes the Poulan Pro range of chainsaws excellent value for money. For the average homeowner, Poulan Pro chainsaws are a good mid-level quality that will get the job done around the yard.
How do you adjust the carburetor on a chainsaw?
How to Tune a Chainsaw Carburetor
- Start your saw and run it for a few minutes to warm it up.
- Set your saw down, let it idle for 30 seconds, and then pick it up and tip it forward (handle up and bar down).
- If it keeps running, go to Step 4.
- Rev (accelerate) the idling saw.
- If it accelerates fine, go to Step 6.