FAQ: How To Identify Walbro Carburetor Model?

How do I tell what model my carburetor is?

The list number is stamped on your carburetor, either on the corner of the airhorn or choke tower or, if it doesn’t have an airhorn, on the mainbody. Remove the carburetor from your vehicle before looking for the list number to easily find the information you need.

What is a carburetor number?

It’s like a “VIN” for your carburetor and should be hand-stamped on the front of the choke tower to the right of the vent tube on most typical Holley carbs. The list number typically is four to six digits long and may or may not have a suffix number behind it. The date code will be right below it.

Who makes Walbro carburetors?

Mark McGeary, Purchasing Manager, Polaris Industries Inc. Walbro has demonstrated outstanding performance in terms of quality, cost competitiveness, on-time delivery and flexibility.

How do I know what model my Keihin carb is?

Look at the carburetor itself. You will find a number that is usually preceded by two to three letters. This is your model number. This number is needed for all parts orders or repair assistance.

You might be interested:  Readers ask: How To Adjust A Carburetor On A 12 Horse Briggs & Stratton Motor?

What size carburetor do I need for a 350?

A 600-cfm carburetor may perform quite well on a stock 350 Chevy. However, the minute you start weaving in power adders like a hotter cam, a dual-plane performance intake manifold, and aluminum heads you’re going to need 700-750 cfm.

How do I know if I have a 2 barrel carburetor?

Autolite 2 barrel tuning To identify your carb you need the Ford tag number which is stamped into a triangular shaped aluminum tag under one of the fuel bowl screws. The numbers on that tag are the carb identification number, the design code and the production date code.

How do I know what Rochester carburetor I have?

All Rochester Quadrajet carburetors are identified by a seven- or eight-digit GM part number. On units made before mid-1968, the part number was stamped around the outside edge of a round metal tag attached to the fuel bowl.

How do I know what Weber carb I have?

Weber model numbers are always stamped on the carburetor body. They always begin with a 2-digit number (or a pair of 2-digit numbers separated by a slash) followed by three or four letters. There may or may not be more numbers and/or letters after that.

Are Walbro carbs good?

Only good thing is the carbs are dirt cheap to replace when they foul up. And they will foul up no matter how picky you are with fuel quality. Zama is owned by Stihl or part owned by Stihl and has their main factory in Japan. They are excellent carbs,no better or o worse than the equivalent Walbro.

Where are Walbro carburetors manufactured?

Walbro is a global organization, headquartered in Tucson, Arizona, with over 2300 employees worldwide. The company has ISO certified manufacturing and engineering facilities in the United States, Japan, Mexico, Thailand and China.

You might be interested:  FAQ: How To Switch From Carburetor To Fuel Injection?

What is the smallest Walbro carburetor?

The WA/WT series includes our smallest diaphragm carburetors, designed for engines from 14 to 50 cc. Meets all CARB and EPA regulations.

How do I know if my carburetor is rich or lean?

Q: How Do You Tell if a Carburetor Is Rich or Lean? A: One way to tell for sure is by “reading” the spark plugs. If the plug tip is white, the mixture is lean. If it’s brown or black, it’s rich.

How do you adjust a high and low carburetor?

Locate the two fuel-adjustment screws on the side of the carburetor. One will be labeled “Hi” and the other “Lo.” The “Hi” screw regulates the engine at full throttle and the “Lo” regulates the fuel when the engine is idling.

What are the two screws on a carburetor?

Find the adjustment screws on the front of the carburetor. There should be two screws on the front of the carburetor, which are used to adjust the air and fuel mixture. Often these look like flat-head screws and you can use a screwdriver to turn them, adjusting the amount of fuel and air mixing in the carb.

Leave a Reply

Your email address will not be published. Required fields are marked *